#WHATSIZE SCREWS FOR AC SERIES#

Multifunction – 6-In-1 – Oilman series Power System.

Multifunction – 6-in-1 Power System – Cat ® Power.

Multifunction – 6-In-1 Power System – Kubota.

Direct-Transmission Mounted Multi-Power Systems.

Gas Powered Air Compressors & Air Compressor/Generators.

Plug the power cord into a properly grounded 3-prong outlet.ģ. Read the Control Panel Operations section for instructions on all modes and settings for your air conditioner unit.How To Size An Air Receiver Tank | Sizing Formula & More

Cut to size and attach weather stripping as needed.ġ.

Inspect all of the potential air gaps around the window opening.

In order to minimize air leaks, this unit comes with weather stripping that should be installed as needed to plug any gaps that may be present after you have secured the air conditioner into the window.

Slide the insulation panels into each side curtain as shown below with the pattern side facing inward (indoors).

Locate the insulation panel supplied with this unit and cut each panel to the correct width.

Start by measuring the inner width of both side curtains.

This unit comes with insulating sheets that should be installed into each of the side curtains to maximize energy efficiency.

#WHATSIZE SCREWS FOR AC INSTALL#

Install Energy Efficient Insulation Panels

Trim the window sash seal (foam) to the appropriate length and insert it into the gap that is between the upper and lower window sashes.Ģ.

Once installed, the bracket will prevent the lower window sash from being raised upwards.

Use two (2) ½” Philips head screws to attach the bracket to the upper window sash.Secure the lower window sash to the upper window sash with the Window Lock Bracket.Note: Use a 1/8” drill bit to drill pilot holes in the window sash to prevent splitting before driving the screws into place. Use three (3) ½” Philips head screws to attach the side curtain frame and top channel to the window sash.Note: Use a 1/8” drill bit to drill pilot holes in the window sill to prevent splitting before driving the screws into place. Repeat this procedure for the remaining side curtain.Use one (1) ½” Philips head screw to attach the Curtain Brackets to the window sill.Place the Curtain Bracket in between the accordion extensions as shown in the image below.The Curtain Brackets will secure the lower frame of the side curtains to the window sill.Extend both Side Curtains outward until they are flush with the window frame. Depending on the adjustment needed, shims may be used on the interior side of the sill or the exterior side of the sill to achieve the proper slope.Ģ. Insert shims below the cabinet frame on the window sill and check for proper rearward tilt. Tip: Small wood shims (available at home supply stores) are a quick and easy solution to create the proper rearward slope. After proper installation, condensation should not drain from the overflow drain hole during normal use, correct slope or otherwise. Note: Check that the air conditioner cabinet is tilted back about 1⅛” to 1½”, which should be about 3-4 degrees downward to the outside. Measure the distance of the right side and left, and adjust until the unit is perfectly centered.Maintain a firm hold on the cabinet and lower the window sash to hold the cabinet in place.Check that the lower rail of the air conditioner cabinet is behind and against the back side of the window sill.Center the air conditioner cabinet into the window: Note: When choosing your window make sure the power supply cord is within 4 feet of a grounded 3-prong outlet.ġ. Insert the top and bottom of the curtain housing into the top curtain and bottom curtain channel. To attach the side curtains to the air conditioner, start by gently extending the accordion panel until you can insert the open end into the connector tabs located on the side of the unit.ĥ. Use four (4) 3/ 8” Phillips screws to attach the top channel to the top of the cabinet.Ĥ. Place the top channel on top of the air conditioner cabinet, lining up the four (4) holes in the top channel with the four (4) holes on top of the cabinet.ģ. Set the air conditioner unit on a table or other solid work surface.Ģ. Make sure to attach the top channel and side curtains prior to installing the cabinet into the window.ġ. Window Air Conditioner Installation Instructions

#WHATSIZE SCREWS FOR AC FULL#

The following measurements are required to properly install the air conditioner.Ĭlick the below link to download a full copy of all installation instructions: See the power requirements listed on the product label printed on the side or the back of your window air conditioner. If you have multiple windows, choose one that is near an electrical outlet that will be able to provide sufficient power to your unit. Before you begin, make sure you have all the parts necessary for installation.

Whatsize screws for ac